Add group to favorites
Back to post list
Send new message to group Search:
Post Subject:
Kenwood KGC-9042 EQ power connector pinout
Kenwood KGC-9042 EQ power connector pinout
I have one of these, (low profile electronic presettable) but it came
to me without the power connector. Its a common type, I robbed one off
an old computer power supply (4 pin). I can get it to power up, but
cannot identify which wire is for memory and which is the power on
lead. Anyone have one of these? Can ya take a peek 'round the back and
ID the wiring at the connector for me?
I have one of these, (low profile electronic presettable) but it came
to me without the power connector. Its a common type, I robbed one off
an old computer power supply (4 pin). I can get it to power up, but
cannot identify which wire is for memory and which is the power on
lead. Anyone have one of these? Can ya take a peek 'round the back and
ID the wiring at the connector for me?
Re: Kenwood KGC-9042 EQ power connector pinout
In article <154f9f1e-382f-421c-b384-
62da48bcfe7a@n77g2000hse.googlegroups . com >, boardjunkie@techie . com
says...
> Kenwood KGC-9042
>
For $10 you can get the owners manual here:
* tinyurl . com /ys6qzo
Don't know if it shows wiring or just an operators manual.
--
I. Care
Address fake until the SPAM goes away ;-}
In article <154f9f1e-382f-421c-b384-
62da48bcfe7a@n77g2000hse.googlegroups . com >, boardjunkie@techie . com
says...
> Kenwood KGC-9042
>
For $10 you can get the owners manual here:
* tinyurl . com /ys6qzo
Don't know if it shows wiring or just an operators manual.
--
I. Care
Address fake until the SPAM goes away ;-}
Re: Kenwood KGC-9042 EQ power connector pinout
boardjunkie;2276775 Wrote:
> I have one of these [ ... ] I can get it to power up, but cannot
> identify which wire is for memory and which is the power ..
If you've managed to get it powered up, and if I recall correctly there
are only 4 wires (Accs, BATT, rem and ground) then set a preset, then
remove one of the two wires you're using for power for a few seconds,
the repower the unit and see if you've lost the preset -- if not, the
one that remained powered is the Battery contant.
Here's the manual for that unit (free at kenwoodusa . com )
* tinyurl . com /2782wk
greetings
--
Lee
------------------------------------------------------------------------
View thread: * stage.caraudioforum . com /vb/showthread.php?t=296837
CarAudioForum . com - Usenet Gateway w/over TWO million posts online!
boardjunkie;2276775 Wrote:
> I have one of these [ ... ] I can get it to power up, but cannot
> identify which wire is for memory and which is the power ..
If you've managed to get it powered up, and if I recall correctly there
are only 4 wires (Accs, BATT, rem and ground) then set a preset, then
remove one of the two wires you're using for power for a few seconds,
the repower the unit and see if you've lost the preset -- if not, the
one that remained powered is the Battery contant.
Here's the manual for that unit (free at kenwoodusa . com )
* tinyurl . com /2782wk
greetings
--
Lee
------------------------------------------------------------------------
View thread: * stage.caraudioforum . com /vb/showthread.php?t=296837
CarAudioForum . com - Usenet Gateway w/over TWO million posts online!
Re: Kenwood KGC-9042 EQ power connector pinout
On Feb 24, 2:52 am, Lee <Lee.359...@no-mx.caraudioforum . com > wrote:
> boardjunkie;2276775 Wrote:
>
> > I have one of these [ ... ] I can get it to power up, but cannot
> > identify which wire is for memory and which is the power ..
>
> If you've managed to get it powered up, and if I recall correctly there
> are only 4 wires (Accs, BATT, rem and ground) then set a preset, then
> remove one of the two wires you're using for power for a few seconds,
> the repower the unit and see if you've lost the preset -- if not, the
> one that remained powered is the Battery contant.
>
> Here's the manual for that unit (free at kenwoodusa . com ) * tinyurl . com =
/2782wk
>
> greetings
>
> --
> Lee
> ------------------------------------------------------------------------
> View thread: * stage.caraudioforum . com /vb/showthread.php?t=296837
>
> CarAudioForum . com - Usenet Gateway w/over TWO million posts online!
Ahh...thanks for the manual link. I looked for it but only saw the one
for the larger electronic EQ. Looks like it stores presets internally
since there's only acc pwr, dimmer, and control leads.
On Feb 24, 2:52 am, Lee <Lee.359...@no-mx.caraudioforum . com > wrote:
> boardjunkie;2276775 Wrote:
>
> > I have one of these [ ... ] I can get it to power up, but cannot
> > identify which wire is for memory and which is the power ..
>
> If you've managed to get it powered up, and if I recall correctly there
> are only 4 wires (Accs, BATT, rem and ground) then set a preset, then
> remove one of the two wires you're using for power for a few seconds,
> the repower the unit and see if you've lost the preset -- if not, the
> one that remained powered is the Battery contant.
>
> Here's the manual for that unit (free at kenwoodusa . com ) * tinyurl . com =
/2782wk
>
> greetings
>
> --
> Lee
> ------------------------------------------------------------------------
> View thread: * stage.caraudioforum . com /vb/showthread.php?t=296837
>
> CarAudioForum . com - Usenet Gateway w/over TWO million posts online!
Ahh...thanks for the manual link. I looked for it but only saw the one
for the larger electronic EQ. Looks like it stores presets internally
since there's only acc pwr, dimmer, and control leads.
